|
|
SANDER  = photo available |
| Ref# |
Make |
Description |
8120F
|
A.E.M.
|
One (1) Used A. E. M. 103-520 AP, 52" Single Head Widebelt Abrasive Planer. 150 H.P. to the top smooth steel contact roll (abt. 9-1/2 dia.); separate 15 H.P. hydraulic unit for compensating feed rates of 30-75 FPM. Wt. 17,000 lbs. Air tensioning, electric eye tracking, powered thickness adjustment from 0 - 5", 103" belt length, air disc brakes, set of pinch rolls (one before & one after contact roll), grooved top infeed roll to yield for varying thickness, built in dust collection, 18" extended infeed conveyor (now about 38"), up to 1/4" stock removal, heavy 3/8" thick rubber conveyor belt. Additional equipment includes: Percent load meter, built-in controls, and separate starter for 440/60/3 (if still available).
|
8121F
|
A.E.M.
|
One (1) Used A.E.M. Model 400 AP 42" Abrasive Top Planer. Wt. 16,000 lbs. Hp: Contact Drum: 125 HP, "V"-belt, Feed Belt: 20 HP hydraulic, Controls: Push button start/stop, E-stop, 200 amp disconnect, Starters: Connected for 440/60/3 operation (Size 5). Abrasive Belt Size: 40" x 103", Feed Belt: 39" wide x 1/4" thick
Tracking: Electric eye, Tensioning: Pneumatic, Contact Drum: 9-1/2" dia., smooth steel, Pinch Rolls: Two in, two out. CAPACITIES: Width to 38", thickness to 7". Stock removal to about l/4". Speeds variable from 20 to 80 FPM.
|
8382Q
|
AEM
|
One (1) Used AEM 24” Sander
|
8122F
|
CEMCO
|
One (1) Used Cemco URF-37" 3000 series Wide Belt Sander. Two top heads (one 40 H.P. rubber 10" contact roll, and one 30 H.P. 4" finishing platen), with 1-1/2 H.P. vari-drive feed belt for speeds 15-60 FPM , with motorized bed hoist for 6" heights, with 18" extended infeed, with rubber pinch rolls and anti-kick-back fingers. Dimensions are about 7' wide x 8' long. Wt. 9,775 lbs. Equipped with electric eye tracking, air tensioning, 103" belt length, load meters, air brakes, emergency operator stop bar, dust hoods and size 3 starters currently connected for 440/60/3.
|
8469SS1
|
COE
|
One (1) Used Coe 52” Sander, model 153, 100Hp, 1 head 53” sander, built 1971, Shop Order 83882.
|
8161H
|
COE
|
One (1) Used Coe Tidland 4' Sander, Model 653, 6 Head,. Primary heads opposed to 250 HP, secondary heads opposed to 150 HP, finishing heads off set 100 HP, Polishing Bars, PLC, Control Panels, Duct work to header. Has all systems. Good Shape. Will include $80,000 worth of rolls with it that was rebuilt by Tidland.
|
8346II
|
KIMWOOD
|
One (1) Used Kimwood 6 Head Wide Belt Sander 52”. First Head 150Hp; Second Head 125Hp; Third Head 100Hp; 50Hp AC/DC Feed. All Heads with Magnetic Brakes. Includes Dust Hoods, Controls and New Parts. Ready to Ship.
|
6648A
|
Kimwood
|
One (1) Used Kimwood 8-Head Panel Master Sander. 66 inch width capacity. Left hand flow. Primary and Secondary heads are opposed contact type. 200 HP and 150 HP. Finish heads are offset combination type. 150 HP and 125 HP. Maximum opening is 11˝”. Manufactured in 1987. Excellent machine for MDF or Particle Board application
|
8392A
|
KIMWOOD
|
One (1) Used Kimwood 6” x 12”, 4 Sided Abrasive Planer Sander. Includes two (2) top sanding heads, two (2) bottom sanding heads. Has right and left side heads, 1-15/16 inch spindles Steel Infeed rolls are air tensioned and driven by variable speed D.C. drive. Feed speeds to 40-400 FPM. Sander was reconditioned and then used only a few months. Motors are 440-volts. 51” from floor to infeed bed, 6’ wide, 11’ long, Uses a 13” belt, should run 12.5” material perfectly.
|
8123F
|
RAMCO
|
One (1) Used Ramco 43B series 84, 43" bottom head Abrasive Widebelt Sander. Wt.5,500 lbs. Hp: Contact Roll: 50 HP, "V"-belt, Feed Belt: 1 HP vari-drive, Motor Windings: 9-lead, 220/440, Controls: 110 volt, push button, Starters: Connected for 220/60/3 operation (Size 4). Roll Type: Rubber, serrated, 10 " dia., Abrasive Belt Size: 43" x 84", Tracking & Tensioning: Air, Head Placement: Bottom
Emergency Braking: Drum, Hold-Up Rolls: Seven steel, four rubber. CAPACITIES: Max. Width: 43", Thickness: 0" to 4", Speed: Variable 30-90 FPM
|
8160H
|
Timersaver
|
One (1) Used TIMESAVERS 300 Series, model 343 Sander- 4 KAICBT-3 Top Heads, 1 50 HP Helical planer Head , 1 40 Hp sanding drum, Vacuum Bed, AB1336 Plus
|
6590DD
|
Timersaver
|
Model 352B 1AHD, serial no. 7269
11” dia. by 53” wide steel contact drum followed by a 7” dia. steel smoothing drum
6” dia. rubber covered feedrolls.
Air tracking with controls Air bag holddowns on feed
Feeds from right to left from operator’s side Includes operator’s control panel and loadmeter
5 hp variable speed feed motor Full width panel brush on top
Two (2) 8” dia. dust pickups
100 hp motor. Motor is not included but pulley, brake disc and brake calipers are.
Measures 6’10” front to back, 9’wide (plus motor), 8’4” high
|
8124F
|
TIMESAVER
|
One (1) Used Timesaver 2130, 30" Single Head Widebelt Sander. 30 H.P. "V" - drive to the 6" dia. spiral soft rubber contact roll and separate 2 H.P. vari-drive feed for speeds range of 20-60 FPM. Wt. 3,500 lbs. 66" wide x 75" deep x 88" tall. With pneumatic tracking and tensioning; 75" belt length; 1 H.P. panel cleaning brush; manual bed hoist to 4" thick; disc brake; load meter; 15" infeed; steel pressure rolls, 110 volt control circuitry; dust hoods; size 3 starter presently for 220/60/3 operation.
|
6481
|
Timesaver
|
Timesaver 352B Sander
|
8159H
|
Timesavers
|
One (1) Used TIMESAVERS 300 Series, model 343 –SANDER 4 KAICBT-3 Bottom Heads, 1 -50 HP Helical planer Head , 1 -40 Hp sanding drum, Vacuum Bed, AB1336. 43” x 75” Abrasive Belts. Feed Motor 220-440/3/60.
|
Back
to Machinery Listings