Back to Machinery Listings

RESAW_ROLLFEED = photo available
Ref#	Make	Description
8174A	Doledene	One (1) Used Doledene 38” MK II Vertical Band Resaw. 3½” wide wheels. Tilting non powered adjustable fence. Includes Starters. Wheels are driven by a 25 HP TEFC 230/460 volt motor. Resaw was originally equipped with a hydraulic driven pressroll on the outside of saw but mechanism is missing except for the hydraulic built-in.
8091A	JLT	One (1) Like New JLT Model #79K-7 Door Clamp Machine was used for one week. 38” x 84” maximum capacity, 2 horizontal pneumatic clamps, 4 vertical pneumatic clamps, One lever operation. 400 lbs of clamping force per cylinder, 45 Degree working angle, Designed for stile and rail cabinet doors. Shipping dimensions: 112”L x 68”H x 42”. Weight 675 lbs.
8177A	Kikukawa	One (1) Used Kikukawa Type KV-43 Vertical Rollfeed Resaw, 43” diameter wheels are 4½” wide. Maximum capacity is 12” outside sawline and 16” inside sawline. Maximum depth of cut is over 20”. 30 HP, 460V Toshiba motor. Air setworks.
8126A	KIMWOOD/TRI-STATE	One (1) Used Kimwood/Tri-State Model T-36-4 36" Single-Band Tilting Roll Feed Resaw. Will either self-center or gauge saw. Feed rolls tilt up to 45-degrees. Feed speeds from 10 to 250 FPM. 3-1/2"-wide wheel for 4"-wide band or narrower. Maximum capacity is 6"- x 8"-wide stock. Usual saw kerf is 1/16". 25 HP, 220/440-volt motor 50/60-cycle. Feed rolls driven by two 1 HP, DC variable-speed motors powered by SCR control unit. Wt. 200-lbs.
8293K	LOBO	One (1) NEW Lobo Mult. Slice Thin Rip Frame Saw Model No: Trs-150F Width 0.75" ~ 6", Height 1.25" ~ 7.865", Finish Material Thickness > 0.094", Thickness of Saw Blade 0.043" ~ 0.055", Main Motor 15 HP, Feed Motor 1 HP, Feed Speed 1 ~ 5 FPM, Air Pressure 90 PSI, Lubrication System Auto Oil Lubrication, Cooling System Water & Air, Machine Size 142" x 32" x 75", G.W. 5800 LBS, N.W. 5070 LBS.
8577	McDonough	McDonough 54" Tilting Rollfeed Resaw. with bearings mounted in wheel. Top wheel is 5/8"-thick at edge of rim. Feedrolls driven through 5-speed gear box. 440/3/60 drive motor. Maximum stock size is 18"-wide x 24"-high. tilt 15-degrees.Older machine in good operating condition.
5569	McDonough	54" McDonough resaw/linebar w/ Merry-Go-Round, Computerized Set Works. Chain Turner board Flippers, infeed and 20Hp Hydraulic power unit and control booth
5708A	MCDONOUGH	One (1) Used 42" McDonough TILTING POWERED FEED ROLLS. 75Hp.
6649A	McDonough	One (1) Used Reconditioned McDonough 54" Tilting Rollfeed Resaw. non-rotating upper wheel shaft with bearings mounted in wheel. Top wheel is 7/8"-thick at edge of rim and has 7-1/4"-wide face. Feedrolls driven through 5-speed gear box from 40-220 FPM, 50 HP, 440-volt wheel drive motor. Maximum stock size is 18"-wide x 24"-high. tilt 15-degrees. Pressure saw guides. Will either center split or gauge saw. Air-operated roll opening.
8178A	McDONOUGH	One (1) Used McDonough 54", Mechanical Strain Tilting Rollfeed Resaw. Older round column model, but has almost new high-strain top wheel. Maximum depth of cut is 30". Maximum opening is 18". Tilts 7-degrees. Will center split or gauge saw. Top wheel is 7/8"-thick at edge of rim, and 7-1/4" wide. Pressure saw guides. Includes one blade, .049 plate, .095 kerf. No motor for wheel or feedrolls. Appears in fair condition.
6561E	McDonough	One (1) Used 54" McDonough Resaw. 2) Available
8071A	McDONOUGH	One (1) Used Reconditioned McDonough 54" Tilting Rollfeed Resaw. Mechanical strain; non-rotating upper wheel shaft with bearings mounted in wheel. Top wheel is 7/8"-thick at edge of rim and has 7-1/4"-wide face. Feedrolls driven through 5-speed gear box from 40-220 FPM, 50 HP, 440-volt wheel drive motor. Maximum stock size is 18"-wide x 24"-high. Will tilt up to 15-degrees. Pressure saw guides. Will either center split or gauge saw. Air-operated roll opening.
8125A	PACIFIC	One (1) Used Pacific Heavy Duty 54” Tilting Feedroll Resaw. Heavy Cast Steel top and bottom wheels have 6” wide faces. Four 6” diameter 12” high feedrolls with ball bearings will either gauge sawing or center splitting and tilt a full 45º. Rolls open 16” (8” on each side of blade) and 14” square stock can be sawn corner to corner at 45º. 3 HP 4-speed Lima feedroll drive gives speeds of 100, 140, 180, and 200 feet per minute, and can also be reversed. Floor space is 5’3” X 6’8”. Floor to top of roll table is 27”. Weight is 8,500 lbs. includes upper wheel guard. No motor. 75 HP recommended.
5707	STETSON ROSS	42" Tilting roll. Hyd. drive. 40Hp. A-1 Condition.
5387	TURNER	48' WITH 6' WHEEL FACE 40 HP MOTOR 2 HP VARI DRIVE FEED DRIVE 13/16 AND 15/26 SAW THICKNESS.
8176A	TURNER	One (1) Used Turner Model E-48, Left-Hand Single Band Tilting Rollfeed Resaw. 5-1/2”-wide solid disc-style wheels. 40 HP, 440V motor with solid state starter. 25º tilting feedroll assembly with variable speed DC inverter drive package 10 to 300 F.P.M upper and lower saw guides. Air-tensioned feedrolls open 6” inside of sawline and 9” outside. Will center-split up to 12” or gauge saw up to 15” cant and up to 24” below upper guide. Uses 6”-wide x 23’-6”x18-21 gauge blades. All roller and ball bearing construction. Weighs 7,500-lbs. Upper wheel guard.
8175A	TURNER	One (1) Used Turner 42” Model TSR Single Tilting Rollfeed Resaw, Four (4) 10-1/2”-tall powered feedrolls tilt up to 35º off vertical, and feed material up to 300 FPM. Maximum stock size is 8”-wide and 14”-high. Wheels are solid cast and have 4-1/4”-wide faces. Saws (not included) are 19’-6”-long, between 19 and 22 gauge (.042” to .028”) plate thickness (add .007” per inch of saw width to determine typical kerf). Includes upper wheel guard, variable speed drive for feedrolls, starters, and 30 HP motor to drive wheels. Saw guides are pressure-type. Feedrolls set on both sides with outside set spring-loaded, with foot pedal to open for wide pieces.
8173A	TURNER	One (1) Used Turner Model E-48 Twin Rollfeed Resaw. 48” Wheels. Self centering feed rolls or one side can be stationary for gauge sawing. Rolls run in ball bearings. Variable frequency A.C. drives for feed speeds from 20 to 300 F.P.M. and two (2) 40 HP 460 volt motors for wheel drives. Upper wheel guard.