|
|
MOULDER  = photo available |
| Ref# |
Make |
Description |
8588
|
All Makes and sizes
|
In stock: 1,000 used cutter heads, for YATES American, Woods, Mattison, Weineg, Wadkin. Planer and Moulder heads
|
8116F
|
DIEHL
|
One (1) Used Diehl D-512, 12" x 4" Four Head (provision for a fifth head) Electric Push-Feed Moulder with random length hopper feed attachment. Weight – 12,500 lbs. Overall Dimensions – 12-1/2' L x 5-1/2' W. Hp: Top Head: 15 HP
Left Side: Appx. 7.5 HP, Right Side: Appx. 7.5 HP, Second Bottom: 15 HP, Feed: 10 HP vari-drive, Windings: 220/60/3 only (sides), Balance are 220 or 440 (9-lead), Controls: Built in. Spindle Diameters: 1-13/16" sides (horizontal spindles
require integrated cutterhead bodies if used as a 12" machine; otherwise, a short 6" stub (1-13/16") is currently present). Spindle Speed: 3600 or 7200 with high frequency unit (not present), Drive Rolls: Four, 8" diameter, Roll Type: corrugated top, smooth bottom, Roll Drive: Gear Roll Tension: Pneumatic, Sidehead Tilt: 45 degrees inward, 15 degrees outward, Feed Rate: 25-176 FPM.
|
8355FF
|
DIEHL
|
One (1) Used Diehl Moulder, DL606, 9" Wide By 6" High, 6 Head Machine. Spindles Factory Rebuilt, Feed System Rebuilt, Many Heads, 6K And 8K, Mostly Hydro Loc Heads
|
8115F
|
DIEHL
|
One (1) Used Diehl 804, 8" x 4" Four Head Electric Push-Feed Moulder with special equipment; clutch-type random length hopper feed attachment and air loaded top rolls, chipbreaker, top head and pressure bar for fast jam clearing. Weight - 11,500 lbs. Overall dimz: 11-1/2' L x 5-1/2' W. HORSEPOWERS
Top Head: 20 HP direct, Left Side: 10 HP, Right Side: 10 HP, Bottom Head: 10 HP, Feed: 10 HP vari-drive, Windings: 220/440, Controls: Built-in, Starter: Separate panel, now connected for 220/60/3. spindle Diameter: 2-1/8" top & bottom; 1-13/16" sides, Spindle Speed: 3600 rpm, direct. Rolls: Six, 6" diameter
Roll Type: Corrugated top, smooth bottom, Roll Drive: Helical gears, Roll Yield: 1" maximum, Feed Rate: 27-200 FPM
|
8117F
|
Diehl -Vonnegut
|
One (1) Used Diehl Vonnegut 8" x 4", Five Head Electric Push-Feed Moulder with random length hopper feed attachment. Wt. 9,900 lbs. 2' long x 5' wide. Hp:
First Top Head: 15 HP direct, Left Side: 7.5 HP, Right Side: Appx. 7.5 HP, Second Top Head: Appx. 15 HP, Bottom: 15 HP, Feed: 7.5 HP, two-speed, motor Windings: Heads-230/440; Feed-440/60/3 ONLY, Controls: New start/stop
Starters: Presently for 440/60/3. Spindle Diameters: 2-1/8" horizontals; 1-13/16" verticals, Spindle Speed: 3600 rpm, Rolls: Four, 8" diameter, Roll Type: 1st upper-solid,corrugated. 2nd upper-sectional, corrugated, Balance-smooth steel
Roll Tension: Pneumatic, Sidehead Tilt: 45 degrees inward, 15 degrees outward
Speed: Eight separate rates to about 80 FPM.
|
6535A
|
Iida
|
One (1) Used, Iida Model MH-221 5” x 8-5/8” Capacity (125x220mm), 5-Head Through Feed Moulder. 12 powered upper and twelve (12) powered lower feedrolls. Feed speeds to 200 FPM (60m/min). All spindles jointed, except top profile. All horizontal spindles with outboard bearings. All spindles are 50mm, which can be turned back to 1-13/16”, if desired. Spindles are keyless and operate at 6,600 RPM’s. Jointers can be operated while running lumber. Electronic digital thickness readouts. Heads are bottom, left, right, top, top. Motors are, in order, 7.5 HP, 7.5 HP, 10 HP, 15 HP, and 10 HP. Feed motor is 10 HP, variable speed. 220V, 3-phase. Includes two (2) 5” sideheads and two (2) 7” top and bottom cutterheads, all hydro lock style. Had been used very little since new, but has been idle for at least 10-years.
|
8328K
|
LOBO
|
One (1) New Lobo 4 Side Through Feed Moulder, 9" 5 Spindle
Features:
• Hard chrome plated table for maximum wear resistance.
• Fully enclosure safety guard reduces noise and completely prevents chips splashing.
• Anti-impact plate for over-width and over-thickness protection.
• Oversized top and bottom rollers run synchronized, ensuring smooth feeding.
• FRP plastic steel safety guard features maximum durability and impact resistance.
• The Three independent section pneumatic pressure for the infeed rollers, in-process rollers and outfeed rollers can be set with individual pressure allowing for consistent feeding results and outstanding effect.
• The smooth initial feeding of the stock is achieved by the independently powered infeed rollers.
• Exclusively designed template inserted pressure plate suits various stock thickness and profile variations.
• Special pressure plate adapted with table feeding roller design, provides smooth and precise cutting of dry and wet wood, reducing the possibility material jams.
• The machine base is one piece coated from high quality cast iron (FC-25) for maximum stability of structure.
• Base is machined by CNC machine equipment to assure the utmost working accuracy.
• The first bottom horizontal spindle can fit with a trimming cutter for trimming a groove at the work piece side to achieve perfect straightness.
• The specially designed short stock feeding mechanism combined with auxiliary pressure wheels permits the machine to perform machining on extra short stocks.
• All spindles are precision constructed and especially heat treated to provide maximum cutting stability and permanent accuracy.
• Each spindle is provided with a mechanical digital read out, that giving accurate adjustment.
• Every cutter spindle can be adjusts" up and down " and " in and out" for quickly setup.
• Industrial full power motor for maximum cutting capacity.
• Precision sealed long life high speed ball bearing.
SPECIFICATIONS:
Max. (Min.) Working Width 9" (3/4"),
Max. (Min.) Working Thickness 4-3/4" (5/16"),
Min. Working Length 9½",
1st Spindle Horsepower 10 HP,
2nd, 3rd Spindle Horsepower 10, 10 HP.
4th, 5th, Spindle Horsepower 15, 15, HP,
Feed Motor 7½ HP,
Elevation 1½ HP,
Spindle Diameter 40 MM,
Cutter Speeds (RPM) 6500,
Variable Feed Speeds (FPM) 16 ~ 82,
Cutterhead Diameter;
1st Bottom Head 4" ~ 5",
2nd ,3rd Vertical Head 5" ~ 6-1/4",
Top Head 5" ~ 7",
Last Bottom Head 5" ~ 7",
Pneumatic Air 90 PSI (CFM) 5,
Dust Outlet Diameter 5" x 6,
N.W. (LBS) 9800,
G.W. (LBS) 10700.
|
8249K
|
LOBO
|
One (1) NEW 4 SIDE FEED THROUGH MOULDER Model No: SM-236C, 9" - 6 SPINDLE .
Features:
• Hard chrome plated table for maximum wear resistance.
• Fully enclosure safety guard reduces noise and completely prevents chips splashing.
• Anti-impact plate for over-width and over-thickness protection.
• Oversized top and bottom rollers run synchronized, ensuring smooth feeding.
• FRP plastic steel safety guard features maximum durability and impact resistance.
• The Three independent section pneumatic pressure for the infeed rollers, in-process rollers and outfeed rollers can be set with individual pressure allowing for consistent feeding results and outstanding effect.
• The smooth initial feeding of the stock is achieved by the independently powered infeed rollers.
• Exclusively designed template inserted pressure plate suits various stock thickness and profile variations.
• Special pressure plate adapted with table feeding roller design, provides smooth and precise cutting of dry and wet wood, reducing the possibility material jams.
• The machine base is one piece coated from high quality cast iron (FC-25) for maximum stability of structure.
• Base is machined by CNC machine equipment to assure the utmost working accuracy.
• The first bottom horizontal spindle can fit with a trimming cutter for trimming a groove at the work piece side to achieve perfect straightness.
• The specially designed short stock feeding mechanism combined with auxiliary pressure wheels permits the machine to perform machining on extra short stocks.
• All spindles are precision constructed and especially heat treated to provide maximum cutting stability and permanent accuracy.
• Each spindle is provided with a mechanical digital read out, that giving accurate adjustment.
• Every cutter spindle can be adjusts" up and down " and " in and out" for quickly setup.
• Industrial full power motor for maximum cutting capacity.
• Precision sealed long life high speed ball bearing.
SPECIFICATIONS SM-236C
Max. (Min.) Working Width 9" (3/4");
Max. (Min.) Working Thickness 4-3/4" (5/16");
Min. Working Length 9½";
1st Spindle Horsepower 10 HP;
2nd, 3rd Spindle Horsepower 10, 10 HP;
4th, 5th, 6th Spindle Horsepower 15, 15, 15 HP;
7th Spindle Housepower ~
Feed Motor 7½ HP;
Elevation 1½ HP;
Spindle Diameter 40 MM;
Cutter Speeds (RPM) 6500;
Variable Feed Speeds (FPM) 16 ~ 82;
Cutterhead Diameter
1st Bottom Head 4" ~ 5";
2nd ,3rd Vertical Head 5" ~ 6-1/4";
Top Head 5" ~ 7";
Last Bottom Head 5" ~ 7";
Pneumatic Air 90 PSI (CFM) 5;
Dust Outlet Diameter 5" x 6;
N.W. (LBS) 9800;
G.W. (LBS) 10700.
In stock and Ready to Ship Today
|
8381Q
|
MADISON
|
One (1) Used Madison Moulder, Model # 276; 4-Heads,6” Cap. 15hp Top Heads, 7.5hp Bottom Heads.
|
8237V
|
MATTISON
|
One (1) Used Mattison Moulder, model 276 (LO #9) 4x6” Capacity with jointers.
Currently connected to power. Top head is approximately 10 hp with a 2-1/8” arbor. Left head is 10 hp with a tilting 1-13/16” arbor. Right head is 7-1/2 hp with a tilting 1-13/16” arbor Bottom head is 10 hp with a 2-1/8” arbor.
|
8502UU1
|
MATTISON
|
One (1) Used Mattison 276 Moulder,6", 15HP Top And Bottom, 7.5HP Sides, Bevel Chip Breaker, C/W Jointer Bars, Spare Motors, 8-2” Eight Knife Heads And 16’ Grading/Trim Saw Table.
|
8503UU1
|
MATTISON
|
One (1) Used Mattison 276 Moulder, 6”, 15HP Top And Bottom, 10 HP Sides. Bevel Chip Breaker, C/W Jointer Bars, Spare Motors And 8-2” Eight Knife Heads And 16’ Grading/Trim Saw Table.
|
5345
|
MATTISON
|
4 X 8, 4 HEAD 15 HP TOP & BOTTOM 7.5 HP TILTING SIDE HEADS GOOD CODITION.
|
8236V
|
MATTISON
|
One (1) Used Mattison Moulder, model 276 (LO #2) 4x6” capacity with jointers. Top head is 10 hp with a 2-1/8” arbor; Left head is 7-1/2 hp with a tilting 1-13/16” arbor; Right head is 7-1/2 hp with a tilting 1-13/16” arbor; Bottom head is 10 hp with a 2-1/8” arbor.
|
8079A
|
Mid-Oregon
|
One (1) Used Mid-Oregon High Speed Moulder Or Ripsaw Lateral Chain Feed Table. Hydraulic driven with 10 HP hydraulic power unit, air tensioned upper Pressrolls. Powered trim saw with stops for trimming end defects before feeding material to moulder or ripsaw.
|
6658F
|
Sicar
|
Used Sicar SCP 18H5, five-head through-feed moulder. Capacity: 7" wide x 4.5" high; S/N: 15/27. Electrical controls: 440 volt/60 cycles/3 phase. Weight: 3,500 lbs. (1985).
Cutting Sequence: Bottom, right, left, top, second bottom. Horsepowers: 7.5 HP first bottom, right & left share 15 HP, top & second bottom head share 15 HP. Spindles: 6,000 RPM, 1-1/2" diameter where heads go. Feed-Works: 2 HP feed motor, cardan arrangement, with variable speeds 25-125 FPM (estimated).
All adjusting shafts have calibrated dials to facilitate precise and quick changes. Height adjustments are made via control console inputs and gearmotor/hoist drive. Roll tension is by pneumatic cylinders, with steel top infeed and center section rolls and phenolic outfeed rolls. Six foot long straightening table. Includes some dust hoods.
|
5725
|
STETSON ROSS
|
Stetson Ross moulder 5 head, 2x6" capacity.
|
8021A
|
VONNEGUT (Diehl)
|
Vonnegut (Diehl) 4” x 12”, 5-Head Moulder, Variable speed feed. 1-13/16” spindles. Moulder weighs 12,500-lbs. Spindles move freely, but moulder is rusty. Includes jointers and hoods.
Bottom Head 10 HP
Top Head 20 HP
Left Sidehead 7-1/2 HP
Right Sidehead 7-1/2 HP
Bottom Head 10 HP
Feed Motor 3-3/4 – 7-1/2 HP, 2-speed (?)
Motors are 220/440-volt
|
6488A
|
Vonnigut
|
One (1) Used Vonnegut 4 ½ X4” 4-Head Fast Feed Electric Ball Bearing Moulder. Hopper in feed for stacked feeding of short material. Frequency changer for 9,000 RPM’s. Feed Speeds up to 140 feed per minute. Motors for top and bottom spindles have recently been upgraded with new 5 HP Baldor units. Sidehead motors are also 5HP. Feed motor is 4HP. Weight is 5,500 lbs. Parts are available from Diehl Machinery Co. who purchased the Vonnegut line.
|
8466RR1
|
WADKIN
|
One (1) Used Wadkin 6 head Feed through Moulder , GEM 205, 440 volt, Head order BRLTTB,40 mm. spindles, no heads included. Fair Condition.
|
8214R
|
WADKIN
|
One (1) Used Wadkin High Speed Moulder 5 Head, all Heads Jointed. 5 x 9”, Capacity 440/3/60. Electrical Panel.
|
8510TT1
|
WEINIG
|
One (1) Used 1987 Weinig Unimat U17AL 7” 5-Head Moulder. Needs
bottom spindle to be made operational. Standard machine—fixed heads. 220V/440V.
|
8509TT1
|
WEINIG
|
One (1) Used 1984 Weinig Unimat U17AL 7” 5-Head Moulder. All parts;
operational. Standard machine—fixed heads.
220V/440V.
|
8332A
|
WEINIG
|
One (1) Used Weinig Unimat 22A CNC 6-Head Moulder. Head sequence is bottom, right, left, right, top, bottom. Currently equipped with grooved bed for maintaining straight lumber.
|
8506TT1
|
WEINIG
|
One (1) Used Excellent 1988 Weinig Unimat U22AL 9” 5-Head Jointed, Standard Feed
Moulder. Great running condition. Superior throughput of up to 180-200 fpm; we used this machine for high-speed runs up to 140 fpm, and lower-speed high quality runs. 220V/440V.
|
8331A
|
WEINIG
|
One (1) Used Weinig Model Profimat 23E 5-Head Moulder. 4-3/4” X 9-1/16” Capacity. 6,000 RPM spindle speed. 220/440V 15 HP on all spindles. Hydraulic variable speed drive for feedrolls. Full set of 4-knife cutterheads plus seven (7) spare cutterheads. Sound enclosure. Motor starters. Air tensioned upper feedrolls. Some spare parts. Suction system “christmas tree”. Moulder is in very good condition and current owner indicates it is “ready to run”.
|
8508TT1
|
WEINIG
|
One (1) Used Weinig Unimat #U22AL 9” 5-Head Jointed, Tilting Feed Moulder
Outstanding 1987 Machine, Great running condition. Superior throughput up
to 180-200 feet per minute; lower speed for higher quality runs. A versatile, quality machine and a workhorse for your mill. 220V/440V.
|
8505TT1
|
WEINIG
|
One (1) Used 1987 Weinig Unimat U17AL, 7” 5-Head Moulder. Great Running Condition.Standard Machine—Fixed Heads. Excellent High Quality Throughput. Can Be Cranked Up To 100 Fpm When Roughing Out Mouldings. Slower For Highest Quality. 220V/440V.
|
9024
|
Weinig
|
One (1) Used Weinig Model H-23 Hydromat 7 Head Feed Through Straightening Moulder. Machine was new in 1998, was gone through by a Weinig technician in 2007 and then never put into service.
Head sequence and motor sizes as follows:
•First Bottom head - 15 HP
•First Right side head - 15 HP
•Left side head - 15 HP
•Second Right side head - 15 HP
•First Top head - 25 HP
•Second Top head - 20 HP
•Second Bottom head - 25 HP
Specifications
•9-1/16 in x 6-5/16 in capacity
•2-1/8 in diameter spindles to all heads
•6,000 RPM spindle speeds
•Mechanical digital readouts on all
spindles
•4 foot long (short) infeed table with
two driven rollers above the table,
and one driven roller in the table
•Three driven bed rollers in the machine
table
•Pneumatic side pressure roller before
the infeed rolls
•Outboard bearings to all horizontal
spindles (#1,5,6,7)
•Pressure shoe above and throat plate with
wooden insert for the second bottom spindle
•Full safety and sound enclosure around
complete machine with electric lock- out to
stop machine when doors are opened
•Full Cardan/chainless drive system
•Pneumatic pressure to all top feed rollers.
•10 HP variable speed feed works with feed
speeds up to 200 feet per minute
•Very nice dust exhaust manifold with all
drops and connections included.
•Deep chromed bedplates and fences
throughout entire machine.
•Machine includes straight jointers on
heads #1, 2, 5, 6 and 7
•Profile jointers on heads # 3, 4, 5,
6 and 7
•Machine wired for operation on 460 volts,
3 phase, 60 cycles.
•Machine also is offered complete with a
MSL 16 ft length capacity 10 HP
motorized hydraulic lateral infeed
table with feed speeds of 50 to 260 feet
per minute which can be operated alone
or tied in to the moulder feed works
as well. Infeed system originally made
for and supplied with machine by
Weinig USA.
•Moulder alone, when purchased new by
original and only owner in 1998 cost
$224,600 without tooling and infeed
system cost was $27,500. Machine was
completely gone through by Weinig when
removed from service in late 2007 and
never re- installed as plant closed
shortly thereafter. Cost for reconditioning
was over $30,000.
•ALL original paperwork (invoices, etc)
for the original purchase as well as
the reconditioning done are available
upon request.
|
8557
|
Weinig
|
Weinig Model U14N 4-3/4” X 5-1/2” (120 X 140 mm) 7-Head Through-Feed Moulder, Head configuration is bottom, right, left, right, top, bottom, universal. Variable speed from 20 to 118 feet per minute (6 to 36 meters per minute); 6,000 RPM 40 mm spindles. 8’ long infeed apron table. Motors are 4 and 5.5 HP. Includes control panel and some cutterheads.
|
9047
|
WEINIG
|
WEINIG Powermat 400-2007,6 head First bottom head 10 HP
Right side head 10 HP Left side head 10 HP First top head 15 HP Second top head 15 HP Second bottom head 10 HP
Full sound and safety enclosure.
|
8330A
|
WEINIG
|
One (1) Used WEINIG Model U 30 EL 5 Head Feed Through Moulder. 12” x 4-3/4” working capacity Head sequence: 1st bottom 20 HP, right side 15 HP, Left side 15 HP, top 30 HP and 2nd bottom 20 HP. 2-1/8” diameter spindles with cutterhead speed of 8,000 RPM. Outboard bearing supports on top and bottom spindles. All spindles with mechanical spindle brakes and mechanical digital readouts. Digiset readouts for left and top spindles. Mechanical readouts for chipbreaker and pressure elements. 3-1/8” Axial adjustment of vertical spindles . 10 HP variable speed feed motor with feed speeds of 20 118 FPM. Machine is wired for 460 volts. Overhead feed wheels with pneumatic pressure, powered table roller at outfeed. 1.2 m (4 ft.) Infeed straightening table, two driven rollers above the table and one driven roller in the table, including side pressure at infeed table. Sound and safety enclosure with light and mechanical safety interlock. Machine was new in 2003 and was recently checked and fine tuned and has new chromed table plates and fence in excellent condition. Machine was converted from 6,000 to 8,000 RPM spindles speed and includes parts if for the 6,000 RPM. Cutterheads; 1st bottom pre-surfacing spiral cutterhead, (3) 10” 4-knife, (2) 2” 4-knife sideheads and (2) 12” 4-knife cutterheads.
|
8478CC
|
WOODS
|
One (1) Used Woods 134 M Moulder, parts machine, 6” cap. 4 head, Voltage 440/220, Top Head 15Hp, Bottom Head 10Hp.
|
8272V
|
WOODS
|
One (1) Used Woods Moulder, model 808M; 4x4” . 10 hp top, 1-13/16” arbor
5 hp left, 1-13/16” arbor; 5 hp right, 1-13/16” arbor; Approximately 15 hp bottom, 2-1/8” arbor. Good machine
|
5471
|
WOODS
|
4 HEAD, 3'X4', 4-SPEED, MODEL # 808M, MOTORIZED, 5HP TOP & BOTTOM HEADS, 3HP SIDE HEADS, FLOORING MACHINE. 220/60/3 - JUST TAKEN FROM SERVICE - PHOTO.
|
8451CC
|
WOODS
|
One (1) Used Woods 134 BM Moulder, parts machine, 12” cap. 5 head, chrome bed plates. Voltage 440, Top Heads 15Hp, Bottom Head 10Hp.
|
6657F
|
Woods
|
Woods 137 M, 6" x 4", Four Head, Push Feed, Electric Moulder. Weight about 8,000 lbs.
Floor space appx. 9 ft x 3.5 ft.
Highlights: 7.5 H.P. top and bottom head, 5 H.P. left and right sideheads; feed motor not present.
2-1/8" horizontal spindles & 1-13/16 sidehead spindles
Lag bed endless feed chain, with two top 6" driven rolls; Built-in starters present. No tooling.
|
8118F
|
WOODS
|
One (1) Used Woods 132 6" x 4" Four Head, Belt-Driven Ball Bearing Moulder, with head sequence of top, left, right and bottom. Wt 10,950 lbs.
All cutterhead belts are internal to the frame. Built in 1200 RPM countershaft equipped with external hanger box, belts, belt tighteners, and "V" drive sheave with belts (no motor--approx. 30-50 HP required.) Feeding is thru two top rolls 6" dia. (Sectional and corrugated and/or smooth), and two bottom rolls 7" dia (solid smooth). Chipbreakers are sectional and spindle diameters are 2-1/8" horizontals and 1-l3/l6" verticals. Feed rates are in the l7-150 FPM . Additional equip. Includes: chromed replaceable beds, 6" top square slip-on cutterheads, 6" bottom round cutterhead/w corrugated knives, 3' infeed table with spring hold-over, and 3 holdowns.
|
Back
to Machinery Listings