Back to Machinery Listings

JOINTER = photo available
Ref#	Make	Description
8099F	HOLZ	One (1) Used Holz Superolimpia 12" Jointer/Sander, continuous abrasive belt. Weight approximately, 1,500 lbs. 5.5 H.P. "V"-drive sanding belt with mechanical tracking, tensioning and forming a top 2" platen where normally a cutterhead would be. Belt also is provided with an oscillating mechanism. With two 22" x 13" individually adjustable steel tables and 23" x 5" tilting fence. Additional equipment includes: a built-in 2 H.P. single phase blower; heavy 2-roll stock feeder with 4" diameter rubber rolls; and starter connected for 220/60/3 operation.
9017	Industrial	One (1) Used Industrial Model 3496/3550, High Production FingerJointer. This fingerjointer system consists of an Industrial Model 3496 dual fingerjointer shaper, and industrial Model 3550 hydraulic assembly machine. The fingerjointer chain is a Bonfield BL-62003 cast-iron feed chain complete with lugs on 9" centers frequency driven for a variable lug speed from 60-90 lugs per minute. Airbag pressure head system, complete with brush hold downs. Include is an Apquip glue applicator. The head motors are 10HP, and the trim saw motors are 3 HP. Two sets of ACE 8 bolt hydra-lock cutterheads. The Industrial Model 3550 assembly is a high production machine, equipped with hydraulic squeeze and carriage travel. It is a continuous feed machine, having traveling cut-off-saw, enabling uninterrupted feed speeds, variable from 50 to 200 FPM. It has a 16' outfeed. Infeed section to a flat top chain to eliminate any overlap problems, with side alignment rolls. This fingerjointer system was reconditioned by Bonfield Industrial Services in September of 1999, was in service for about 5 years.
8084A	INDUSTRIAL	One (1) Used Industrial Model 3496/3550, High Production Finger-Joint System. This finger-joint system consists of an Industrial Model 3496 dual finger-joint shaper. The chain is a Bonfield BL-62003 cast-iron feed chain complete with lugs on 9” centers frequency driven for a variable lug speed from 60-90 lugs per minute. Airbag pressure head system, complete with brush hold downs. Include is an Apquip glue applicator. The head motors are 10HP, and the trim saw motors are 3 HP. Two sets of ACE 8 bolt hydra-lock cutterheads. The Industrial Model 3550 assembly is a high production machine, equipped with hydraulic squeeze and carriage travel. It is a continuous feed machine, having traveling cut-off-saw, enabling uninterrupted feed speeds, variable from 50 to 200 FPM. It has a 16’ outfeed. Infeed section to a flat top chain to eliminate any overlap problems, with side alignment rolls.
8449V	INDUSTRIAL	One (1) Used Industrial 3470 Shaper Section Finger-Jointer With A 3550L Press Section. Includes An AES Automatic Lug Loader. A Scoring Saw Has Been Added To The Second Shaper Column For Cleaner Joints. This Machine Is Capable Of 4-1/2” Minimum To 36” Maximum Length Blocks. The First Pedestal Is Left-Handed With A 5 Hp End Trim And A 3 Hp Scoring Saw Unit. The Profiling Spindle Is On A 15 Hp Motor. The Second Pedestal Is Right-Handed With A 5 Hp End Trim And A 3 Hp Scoring Saw Unit. The Profiling Spindle Is On A 15 Hp Motor. Ziegelmeyer Triple Chain On 9” Centers (Allows 7-3/8” Space Between Lugs). Apquip Glue Control Unit And Pump Injector With A Digital Block Counter. Taken Out Of Service July 11, 2008. It Is Fully Functional And Connected To Power.
8139H	WESTERN	One (1) Used Western Finger Joint System. 15 HP Cutter Heads, 3 HP Trim Saw, Zigelmeyer chains and hold downs with 48” transfer table. 20 ft assembly table with flying cutoff saw. Complete with hydraulic unit and cutter heads. Priced far below market value.
6271	Western Machinery	1994 Western Machinery MD FJ1542-25D RH Finger Jointer line, 2"x6" capacity, 310 FPM, with dual top and bottom trim saws, 30"x36" slat bed infeed, 12' 2-strand slat bed infeed to first section, 10' 2-strand bed feed to second section, 20' lug type pass through block transfer with brush, ABQUIP Auto Glue system, 14' block assembly section with PLS inline auto press, FLying C.O. saw, dual sizing heads, with all hydraulics, drives and PLC controls
6486I	Western Pneumatic	Industrial model PNOV, 20 HP heads, 3 HP score, 7 1/2 HP Trims, 10 HP Feed, Assembly table with 3- 7 1/2 HP Trims, 24' long. Includes heads, glue system. Excellent condition.